You can directly order from various graphic packages for your new snowmobiles these days. OEMs make getting snowmobile graphics much easier, and customers will be able to personalize or customize their new sleds. Most snowmobile makers will offer several options in order to satisfy various tastes and needs. These are great because factory-made graphics are a lot better in fit and finish, giving you the best quality possible.
Aftermarket packages can create a more dynamic look for your snowmobiles. These days, there are two types of plastic surfaces for snowmobiles, smooth and rough. The smooth surface is almost as shiny as a car's paint job. The rough one isn't as glossy and is a bit textured, somewhat like a belly pan. Graphic application in these cases differ as well. Smooth surfaces require a wet method, and rough surfaces will require dry installation. The rough surface needs a dry application so the graphic sticks better.
A machine will be required to install the graphics on the panels. This is a great way to keep the panels secured. Additionally, whoever is installing the graphic alignment can work on it consistently.
During rough surface installations, you'll need to clean your hands before you start so you don't dirty the sticky section of the graphic. Start with the corner of the graphic, and place it on the panel using your fingers. You don't want to have any air bubbles visible on it, so peel it back and try again if there are.
Afterwards, you should add some heat into it. This step is optional, but it will help tighten up the corners and will alleviate the wrinkles on the graphic. If you add too much heat, the graphics can get damaged or shrink too much, so keep that in mind.
The smoother surfaces will need to be clean before you start your application. Spray your fluid or soapy water on the sticky area of the graphic, as well as the surface. Dripping fluid is perfectly fine. You will then lay the graphic down and move it into the right position. Then, you should squeeze the fluid from the center of the graphic all the way out.
Don't trap any fluid in the center. This will be a pain to remove later on. The excess fluid is similar to the air bubbles you might find in the rough surface applications.
Once your graphics are installed, you can trim some of the edges off. However, if you've done a good job, you won't need any trim on it. Use a razor knife to trim the edges, leaving at least a fourth of an inch from all the edges. This will make your graphic look much more professional and appealing. It will also help not make the graphic catch on anything.
After you install your graphic with either the dry or wet methods, step back and take a hard look. The affect your graphics package has will be very noticeable, in the best possible way. Riding your snowmobile will be a whole lot more enjoyable with this fresh new look. You will not regret your decision to add new character to your sled.
Aftermarket packages can create a more dynamic look for your snowmobiles. These days, there are two types of plastic surfaces for snowmobiles, smooth and rough. The smooth surface is almost as shiny as a car's paint job. The rough one isn't as glossy and is a bit textured, somewhat like a belly pan. Graphic application in these cases differ as well. Smooth surfaces require a wet method, and rough surfaces will require dry installation. The rough surface needs a dry application so the graphic sticks better.
A machine will be required to install the graphics on the panels. This is a great way to keep the panels secured. Additionally, whoever is installing the graphic alignment can work on it consistently.
During rough surface installations, you'll need to clean your hands before you start so you don't dirty the sticky section of the graphic. Start with the corner of the graphic, and place it on the panel using your fingers. You don't want to have any air bubbles visible on it, so peel it back and try again if there are.
Afterwards, you should add some heat into it. This step is optional, but it will help tighten up the corners and will alleviate the wrinkles on the graphic. If you add too much heat, the graphics can get damaged or shrink too much, so keep that in mind.
The smoother surfaces will need to be clean before you start your application. Spray your fluid or soapy water on the sticky area of the graphic, as well as the surface. Dripping fluid is perfectly fine. You will then lay the graphic down and move it into the right position. Then, you should squeeze the fluid from the center of the graphic all the way out.
Don't trap any fluid in the center. This will be a pain to remove later on. The excess fluid is similar to the air bubbles you might find in the rough surface applications.
Once your graphics are installed, you can trim some of the edges off. However, if you've done a good job, you won't need any trim on it. Use a razor knife to trim the edges, leaving at least a fourth of an inch from all the edges. This will make your graphic look much more professional and appealing. It will also help not make the graphic catch on anything.
After you install your graphic with either the dry or wet methods, step back and take a hard look. The affect your graphics package has will be very noticeable, in the best possible way. Riding your snowmobile will be a whole lot more enjoyable with this fresh new look. You will not regret your decision to add new character to your sled.
About the Author:
You can visit www.amrracing.com for more helpful information about Personalize Your Sleds With Amazing Snowmobile Graphics.
Comments
Post a Comment